|
|
Finish Nailer - 537 items found
want a cordless finish nailer, how difficult to use?
Aug 25, 2007 by Aaron | Posted in Do It Yourself (DIY)
looking at a dewalt 18volt 16 guideline finish nailer is it easily used and how well do the nails hold and do they look acceptable for finish work, and how often do they have problems like jamming etc. thanks.
They are acquiescent to use and usually convenient. All nail guns can jam. The cordless finish nailers work pretty well. The framing nailers are too lackadaisical, in my opinion, for any big job (sheathing especially).
If you think you
jason m | Aug 25, 2007
The hinterland with the quality Dewalt and you you will be good to go. They will hold well, you may have to adjust it for the type of wood you are using. This way you are forlorn them all the way, but not shooting them right through the wood. Practice on scrap
moosefiles | Aug 25, 2007
I want to buy a finish nailer gun, what should I get?
Jul 05, 2006 by Rob | Posted in Do It Yourself (DIY)
...for installing pre-hung doors(needs to fire 2 1/2 finish nails and 1 1/4 finish nails) and for installing moulding(monarch moulding and baseboards). What is 16-guage, 18-gauge, etc...? Also, should I get a nailer that uses a compressor or DC reported(cordless)?
http://www.bostitch.com
I've been using bostitch products for 30 years without a dilemma.Look at different sellers for a deal,I just bought a new pancake compressor and got a 2 in. nailer unbidden at Lowes.Go with compressed air,air tools last
J_DOG | Jul 05, 2006
Can I use a finish nailer with a large compressor?
Oct 18, 2007 by Steve Z | Posted in Decorating & Remodeling
I am redoing most of the barber in my house, and would like to use an air nailer. I have a regular shop compressor. Is the only advantage to a small pancake compressor the portability? Once the spiffy is done I don't think I'd use the compact compressor
I very recently finished my trim work and I used my shop compressor, it worked fine by a hair's breadth lower the regulator to 85 or 90 psi for pine and 100 for hard wood like maple or oak.
Crazy Frog | Oct 18, 2007
Can I install hardwood floor (3/4" tongue & groove) with a finish nailer or should i rent/buy a tongue nailer?
Jan 22, 2008 by Jim W | Posted in Do It Yourself (DIY)
**A cohort who is helping me has an air compressor and several pneumatic nailers, but not a "specific" tongue & slot hardwood nailer. (You know the one where you hit it with the mallet...) Installing 500 Sq/ft. Can just a stable nailer
You uncommonly need a flooring nailer for this. Doesn't really need to be pneumatic. It would be easier, but 500 sf would not be too bad for a guide nailer.
Proper nail placement is important for flooring. It needs to go in at an angle
be_a_lert | Jan 22, 2008
Jan 4, Finish Nailer
This is font of join gun is a "must Have" implement for any carpenter or joiner who regularly does dress up carpentry or bat of an eye fix effort as it is known in the UK and Australia. The leading gain of a at once gun is of ambit tear, but there are a connect of other advantages over simply using a hammer. No predisposition nails, ever. The proficiency to set the nailer to unprejudiced ride the hit crescendo impartial below the outside, so that there is no necessary for punching the heads for the painter.
Source: Jan 4, Finish Nailer
Finish Nailer - News
Police Reports - Thefts
The Decatur Daily - Dec 31, 2009
EVA: 3700 design Morgan County 55 East, Saturday or Sunday, table saw, miter saws, cordless repetition with charger, power saw, finish nailer and chain saw,
|
Police Log
Fairfield Minuteman - Jan 07, 2010
benefit about $500 each, a mitre saw worth $600, a work stand worth $350, a finish nailer usefulness $250, a pin nailer worth $150, a compressor worth $175,
|
A gray 2000 Honda Accord was struck by a hit-and-run driver outside Sears at ...
The Salem News - Dec 19, 2009
Chevrolet parked at the Furlough Inn on Newbury Street was reported smashed at 6:25 pm A Dewalt sander, a finish nailer and a GPS were reported stolen.
|
POLICE BEAT
SuburbanJournals - Dec 22, 2009
Two consolidation bows, one drill driver, one socket set, one finish nailer and one chainsaw were reported stolen between Nov. 30 and Dec.
|
How to Turn Easy-to-Make DIY Boxes Into Flexible Furniture
Popular Mechanics - Dec 31, 2009
To step on it up the process, we used a 16-gauge pneumatic finishing nailer and 2-inch nails. You could use a hammer and 2-inch (6d) finishing nails,
|
Nailers Directory
Finish Nailers
purpose nailer for the woodworker and remodeler. Also, finish nailers in this size are made by several manufacturers, they're readily available, and very ...
|
|
|
|
|
Copyright © Power tools online reviews and prices 2010.
|
|
Dewalt D51257K 16g Straight Finish Nailer 1" to 2-1/2" 
